- Joined
- Dec 27, 2001
- Messages
- 9,866
New tool box project
- Thread starter Mike Hughes
- Start date
Help Support Intlwaters:
- Joined
- Dec 27, 2001
- Messages
- 9,866
Nope.. have not made them for years.. take them to the local offroad track.. they will be gone ASAP
- Joined
- Apr 14, 2021
- Messages
- 455
Mike, just realized your old box was only two drawer. Mine looks pretty much like yours, except it's FOUR drawer!!
Would be willing to bet mine was made using a lot of the same design(s) for the drawers. Obviously the outside of the box... The extra drawers are broken up with more slightly smaller areas.
Only writing I found is Plano Tackle Systems.
I'm going back to this old box. At least there's room for my wrenches...
Ken
Would be willing to bet mine was made using a lot of the same design(s) for the drawers. Obviously the outside of the box... The extra drawers are broken up with more slightly smaller areas.
Only writing I found is Plano Tackle Systems.
I'm going back to this old box. At least there's room for my wrenches...
Ken
- Joined
- Jan 2, 2006
- Messages
- 3,106
I have the same box, but it has 2 drawers,
And then two slide out compartment boxes with closing lids on each.
Pretty handy, holds all my hand tools, wrenches, puller, T handle Allen wrenches..
and the slide out boxes hold starter belts, glow plugs, engine parts, a prop or two.. all sorts of handy things to use lakeside..
Made by Plano,, I think I did have to replace the lifting handle,
iirc, I used an igloo cooler handle from academy..
- Joined
- Apr 21, 2008
- Messages
- 568
Mike
Does Eric get one too ? I mean it would be a great step to organize his working table at the race
Does Eric get one too ? I mean it would be a great step to organize his working table at the race
- Joined
- Feb 23, 2003
- Messages
- 4,430
It would be a waste......he never puts anything back. I am not sure his tools even have homes. It all just goes in a pile. At the end of the day, if I am missing a tool, it will be in Eric's apron.Mike
Does Eric get one too ? I mean it would be a great step to organize his working table at the race
- Joined
- Feb 23, 2003
- Messages
- 4,430
Needs some final finish sanding to smooth out the slide. Still trying to work out my drawer stops. I don't want them to slide out completely.
- Joined
- Feb 23, 2003
- Messages
- 4,430
It is not that heavy. 4lbs ish. It is ok. It only goes from work bench to trailer. Then to pit table.
- Joined
- May 21, 2006
- Messages
- 1,828
I did the same yrs ago, they little heavier but last a he'll of a lot longer, mine probably 10 yrs old now
- Joined
- Feb 23, 2003
- Messages
- 4,430
Got some work done. I had to walk away from it for a bit. Some hidden flaws inside the plywood that came our when sanding. Plus I drill a hole for another feature that came thru the front. Was not happy. So patched them up with laminated pieces of wood. Not perfect, but better than building some more parts.
Got all the drawers built as well as the tops
Got second box built as well.
Mocked up the lid stop. Just tacked on with CA for the time being to confirm the design. Going to be 2 for each lid. I think I am going to cut these with another 1 degree in them. They are 46 right now. Want a little more tilt back.
Got all the drawers built as well as the tops
Got second box built as well.
Mocked up the lid stop. Just tacked on with CA for the time being to confirm the design. Going to be 2 for each lid. I think I am going to cut these with another 1 degree in them. They are 46 right now. Want a little more tilt back.
Last edited:
- Joined
- Feb 23, 2003
- Messages
- 4,430
Yes. This weekend will have most of the building done. Then on to do the finishing. I will post more pics tomorrow.
Mike
- Joined
- Feb 23, 2003
- Messages
- 4,430
All done. Both of them. Just in time for nats.
Mark Anderson's tool box. He still needs to customize his for his Allen T handles.
Mark Anderson's tool box. He still needs to customize his for his Allen T handles.
- Joined
- Feb 23, 2003
- Messages
- 4,430
Drawer front slides back into box to get out of the way. It is held in place with 2 pins that index into the top of the drawer cover. Spring loaded. Drawers can almost full pull out minus 1/2". There is a stop that keeps them from coming all the way out. Waxed up the rails and my slight binding issue went away. Top T handle holder tucks back against the lid when closed. Locking all handles from coming out of holder. Tilts out just by opening the lid.
Mike
Mike
- Joined
- Feb 23, 2003
- Messages
- 4,430
Planning to build a wrench index in the bottom right drawer. Right now all the wrenches are jsut tossed in there. Might not get that done before I go.
Rick Sowell
Well-Known Member
- Joined
- May 17, 2007
- Messages
- 483
Nice work Mike
Reed Allen
New Member
- Joined
- Apr 20, 2024
- Messages
- 4
Very nice!! Mike...
Similar threads
