- Joined
- Sep 4, 2007
- Messages
- 3,809
I believe Terry Keeley made some little gauges that slipped through the glow plug hole to check the head clearance. Does anyone have this tool they would part with?
-
If you have bought, sold or gained information from our Classifieds, please donate to Int'l Waters and give back.
You can become a Supporting Member which comes with a decal or just click here to donate.
Tool Wanted Head clearance tool
- Thread starter NAMBA860
- Start date
Help Support Intlwaters:
Kristy Wallace
Active Member
- Joined
- Jan 11, 2022
- Messages
- 29
Old school .Use Solder .or use dial callipers
Or,
Contact Daniel place and see if he has any dial gauges in stock. Look up the manufacturer page he will be there .
- Joined
- Oct 2, 2005
- Messages
- 8,013
Plasti guage..
Amazon
Amazon
- Joined
- Oct 26, 2008
- Messages
- 631
I second the solder and dial calipers. Always works for me . I usually just feel along the smashed out solder with the calipers and find the thinnest reading and that is where the squish is at.
- Joined
- May 1, 2023
- Messages
- 337
there's a huge discrepancy between my squish gauge and solder. like over .005"
- Joined
- Sep 4, 2007
- Messages
- 3,809
That’s kind of what I was seeing myself last night it doesn’t seem to be super accurate
- Joined
- Oct 6, 2019
- Messages
- 1,343
I have gauge from speedmaster works great and not that pricey
- Joined
- Nov 26, 2012
- Messages
- 2,351
I would not use solder. Especially if you’re running tight clearances. Either measure it out or get a clearance tool.
If you’re running .010 or lower it is very important to be accurate.
If you’re running .010 or lower it is very important to be accurate.
- Joined
- May 21, 2006
- Messages
- 1,814
Solder for me, used it for many years. Get the solid type 0.030 diameter.
- Joined
- May 28, 2004
- Messages
- 4,291
Depth mic works for me for 39 years.
- Joined
- May 1, 2023
- Messages
- 337
just throwing it out there that you can use the backside of a caliper to take depth measurements.
- Joined
- Oct 25, 2015
- Messages
- 1,943
Depth micrometer easiest, most accurate method for setting clearance. Highly repeatable, measure deck height at TDC, measure button from touch-down surface to squish band, subtract difference....usually a negative (interference) sum, determine shim thickness needed for desired clearance.
Using used shims (pre compressed) a smidge more accurate, by maybe a couple of 1/10000"....not a big deal.
This isn't rocket science.
Using used shims (pre compressed) a smidge more accurate, by maybe a couple of 1/10000"....not a big deal.
This isn't rocket science.
- Joined
- Oct 26, 2008
- Messages
- 631
When I use the rod in the caliper to do that though I always wonder if I am perfectly flat when I push down and so I do check that way too but I confirm with 30 thou solder and sometimes I even rotate it a couple times over on the same solder and it seems to just smash to what it can smash too. I guess I really just don't think to much on it anymore just get er done and go running.
- Joined
- Apr 27, 2007
- Messages
- 3,510
This is just a decent caliper with a base attachment. 3D printed stand to hold the motor vertical.
Last edited:
- Joined
- Oct 25, 2015
- Messages
- 1,943
Yeah, that base is the key.
- Joined
- Apr 27, 2007
- Messages
- 3,510
- Joined
- Apr 27, 2007
- Messages
- 3,510
Money well spent: https://www.mcmaster.com/2325A45/
- Joined
- Sep 4, 2007
- Messages
- 3,809
That’s kind of what I was seeing myself last night it doesn’t seem to be super accurate
- Joined
- Sep 4, 2007
- Messages
- 3,809
The head button surface seems to be angled not flat as well. I have no problem on the cylinder side with a regular caliper, it’s the head button side.
