Mono boat stands...

[Wasted wages]

Wasted, I would offer to print you a couple stand ends. But the angle would probably be too shallow for your hull.

Which hull are you thinking about?

 

[ricwally]

The hull deadrise angle on the files that I printed from are only 18 degrees. Most mono hulls are going to be more than that. I don't have the capability to change the angle from the file that I have.

 

[john v]

its not a mono stand but did you see the blazer stands that bob makes for the backlash, beautifull

 

[Michael Boundy]

If you screw the PVC stand together instead of using glue, it can be taken apart

 

[Wasted wages]

If you screw the PVC stand together instead of using glue, it can be taken apart

I got one with a boat I bought here on IW..
It was done like that...good idea!

 

[Wasted wages]

The hull deadrise angle on the files that I printed from are only 18 degrees. Most mono hulls are going to be more than that. I don't have the capability to change the angle from the file that I have.

What is the width of your stand?
I'll have to put my angle finder on the bottom and see where it's at. Husselcrafts don't have much of a deadrise ....
I have a 20, 60, 90 mono I can measure...

 

[Wasted wages]

Ski poles & copper elbows.View attachment 311247

Jay, what did you use to attach the joints ?

 

[mr_fons]

My PVC MONO stand has lasted at least 15 years. Easy cheap.
Remember, it’s just a boat stand!I have had mine for 15 plus years.

 

[ricwally]

Wasted the width of the stand is just under 8". The height is right at 3". That might be another issue for you. Probably enough rudder clearance for a .21 mono but, maybe nothing larger.

 

[Jay Boyd]

Jay, what did you use to attach the joints ?

They’re a tight friction fit for now. I might use some BHCS or something eventually.

 

[Wasted wages]

They’re a tight friction fit for now. I might use some BHCS or something eventually.

Any clues on where to find ski pole material?
Yer' talkin' to a Texan...we don't have much skiing weather or ski areas... unless it's on the water..

 

[Jeff Barnes]

Simple wood

 

[mr_fons]

Are you willing to share the STL files for this?

Fons

For several years I have been drawing out simple 2D templates for the V-angle and having master's laser cut in acrylic. I use a router table and flush trim bit to cut marine ply or any wood board into a stand. Drill some 3/4" holes and buy some wood dowel.

For small mono's like 21's I have been direct 3D printing stands in PLA. Sorry I don't have a picture of the actual stand, but here is a screenshot in CAD. I'll add some silicone rubber strip to the areas which contact the hull and on the bottom of the stand so it does not slide around. Probably uses $10-15 worth of material.

View attachment 311236

 

[RaceMechaniX]

Sorry Fons for not replying sooner, I was out of the country. The STL files are quite large. If this does not work I will convert into STEP and you can do the STL conversion.

-Tyler

 

[mr_fons]

Sorry Fons for not replying sooner, I was out of the country. The STL files are quite large. If this does not work I will convert into STEP and you can do the STL conversion.

-Tyler

try sending to my email and see if that works.
[email protected]

 

[RaceMechaniX]

Fons, the zipped file is 32megs. I will try sending, but unlikely it will go through.

 

[RaceMechaniX]

Fons, I emailed you the STEP file.

 

[mr_fons]

From which email? and thanks

 

[RaceMechaniX]

The [email protected] one

 

[mr_fons]

thanks, waiting on it.