ML Boatworks GSX380 Sport 40 38" prototype build

Intlwaters

Help Support Intlwaters:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Very nice makes me wish I had got that instead of the gp
The GP boats run EXTREMELY well, you will not be disappointed.
default_cool.png
 
Thanks guys. I am going to get the decks on the sponsons this week, then start the paintwork. Hope to have more info soon. Kent, I may still sell this one, just depends if sales pick back up or not after the website being down. Talk soon, Mike
 
Anything new on this build Mike??

How much do you want for it...lol! You know you can get the laser guy to cut you another kit and whip that one out for yourself...Ha!

PM me...

-Kent
 
Last edited by a moderator:
Ken, I just need to get the decks on, but its been so cold here messing with epoxy in the garage is going to be tough. I would like to finish the build, and run it before selling it, but right now is tough as I do not have enough sales coming in to rig this thing, so until that happens, it is going to be in a holding pattern. This is the slowest part of the year for sales ya know. I will post pics of the decks as soon as I get them on. Mike
 
Kent, I figured I better step things up and at least get the hull finished, and get the gear as soon as I can. Here is where I am now. Got the top decks on, just have to sand the outside edge flush, then the exterior of the hull is ready for epoxy.

I also want to say this was the easiest sport hydro build I have ever done. I usually dread the sponson top decks (hense the delay), but these things were SO easy to install..just a few of those harbor freight clamps, and some tape, and they went on perfect!

Enjoy, Mike

20150111_110023_zps2c1b0c82.jpg


20150111_110029_zps0206a6c0.jpg


20150111_112022_zpscac1dd54.jpg


20150111_112029_zps454de3f2.jpg


20150112_073020_zpscf5c658f.jpg
 
I also want to say that now the sponson decks are on, this hull is EXTREMELY rigid. There is NO center section twist!

20150112_073028_zpsb3bd546f.jpg


20150112_073042_zpsf6f7f4d9.jpg


20150112_073050_zpsf3c8e91d.jpg
 
Well, some good news, I was able to get the gear i needed ordered to rig this thing. Leopard 5692, 1340kv for 6s, 1/4" drive line, round bottom speedmaster strut, speedmaster 21 rudder, ose 56mm mount, and other various needs. Should arrive next week. More soon, Mike
 
Yep, they will get sanded flush. I wanted to let the epoxy dry a few days that i bonded the decks on with...just clogs up my disk sander when its still mildy soft.
 
Got some more done. Sponsons are sanded, hull epoxied, and now I am fitting the gear. So far, so good! Enjoy, Mike

20150115_174836_zpsf2cba1e5.jpg


20150115_174850_zps518369db.jpg


20150115_174903_zpsa1f5e46f.jpg


20150115_174916_zps0f4c5169.jpg


20150115_174933_zpsd42e5151.jpg
 
The motor is a Leopard 5692, 1340kv, OSE mount, Speedmaster Standard .250 round bottom hydro strut, Speedmaster 21 hydro rudder.

20150120_071148_zps7fcf7dbf.jpg


20150120_071159_zpsf578dd0f.jpg


20150120_071206_zps29b0a8c1.jpg


20150120_071213_zps031e4da2.jpg
 
Last edited by a moderator:
Back
Top