Sold K&B 11 cc + lowers

[Joern Markset]

K&B 7,5 cc lower, modified to fit 11 cc as well as use of tuned pipe. Clean lower in good shape.
$ 90,-
Shipping from $ 22,-
Paypal as FF

K&B 11 cc lower, new flex / teflon liner and new propshaft assy. Nice and clean lower.
$ 100,- SOLD
K&B 11 cc powerhead, good comp, bearings turn smooth (outer pto bearing could probably be replaced, but turns ok)
$ 50,- if purchased together with one of the above lower ends. SOLD

 

[tommyLi]

Hi , I need to K&B 11 cc lower, new flex & K&B 11 cc powerhead, good comp , Goods delivered USA Oregon 97080 how much shipping .

 

[Joern Markset]

Hi , I need to K&B 11 cc lower, new flex & K&B 11 cc powerhead, good comp , Goods delivered USA Oregon 97080 how much shipping .

Hi,
That will be 150 bucks for lower and powerhead, + 25 bucks shippingcost. If you want insured shipping it is 37 bucks.
Shipping on Monday morning if you decide to buy.

 

[tommyLi]

Hi , 150 bucks for lower and powerhead + insured transportation =180 Are you willing to accept , if you accept please give me Paypal .

 

[Joern Markset]

Hi , 150 bucks for lower and powerhead + insured transportation =180 Are you willing to accept , if you accept please give me Paypal .

Ok, I can do that.
You will need to send me your address, e-mail and a phone number you can be reached at. (it is for the shipping documents)
Send paypal to [email protected]
You will receive all necessary shipping info ones the documents have been made.
Thanks
Jørn

Edit: Payment received

 

[tommyLi]

Hi , Recipient to Chi Fai Li , 2893 sw 33RD ST Gresham Oregon USA 97080 , [email protected] , 15039157567 , I have sent to you Paypal account

 

[Joern Markset]

Hi , Recipient to Chi Fai Li , 2893 sw 33RD ST Gresham Oregon USA 97080 , [email protected] , 15039157567 , I have sent to you Paypal account

Document has been made up, a copy along with tracking info has been sent to your e-mail.
Thanks
Jørn

 

[tommyLi]

Thank

 

[tommyLi]

HI , The item has been received and is complete , but there is a problem , The connection between the exhaust port and the lower boby does not match , This can cause exhaust leaks , Yes rejected some parts .

 

[Wasted wages]

Missing the exhaust adaptor plate?

 

[BobSmith1]

the adapter is there, sometimes there's a gap, I've seen where people put a small amount of high temp silicone, here's a new in box, less gap, but still a gap.

 

[tommyLi]

Missing the exhaust adaptor plate?

This is what is not missing

 

[tommyLi]

the adapter is there, sometimes there's a gap, I've seen where people put a small amount of high temp silicone, here's a new in box, less gap, but still a gap.

Shim the crack

 

[tommyLi]

Thank for the guidance

 

[David Krienke]

Shim the crack

In your picture the back of the engine pto looks to have a gap also. I wonder if something is hitting under the pto backplate not allowing the engine to come together with the lower unit. try pulling the flex shaft out and see if it goes together tight.

 

[tommyLi]

There is a gap in the exhaust , and there is no problem with the rear connection

 

[Joern Markset]

I believe there is a gasket sitting on the pto as well, that can be peeled off.
Also make sure you get the pto completely and correct into the crankcasing when thightening up.
Still, as mentioned above, there is often gap to be seen here. You may cut some gasket material and shim out the exh adapter ring.
There is not missing parts.

 

[tommyLi]

The bottom part is flat

 

[tommyLi]

I believe there is a gasket sitting on the pto as well, that can be peeled off.
Also make sure you get the pto completely and correct into the crankcasing when thightening up.
Still, as mentioned above, there is often gap to be seen here. You may cut some gasket material and shim out the exh adapter ring.
There is not missing parts.

Thank

 

[Greg Rowe]

I have had this same issue with 7.5 , 67,& 82
Not sure why but with the gap it will not run correctly, issues with pressure port to tank and loud as crap.
I suggest a garloc gasket material thick enough to apply pressure and not leak.
Just a thought