Search results

mike i can not believe you are selling this boat i wish i had the money but i just bought the scale boat. well let me see what i have under the mattress. i will give you a call

A 85-year-old man went to his doctor's office to get a sperm count. The Doctor gave the man a jar and said, "Take this jar home and bring back a Semen sample tomorrow." The next day the 85-year-old man reappeared at the Doctor's' office and gave him the jar which was as clean and empty as...

try to put a straight edge across the bottom long ways of the hull i had one and at the transom on each side of the tunnel it had a lip. the lip produced down foce on the nose. if you sand it down until it is smooth no hook it will free up the nose. also check your strut angel raise the rear of...

Just to let you know i like dick and he has always returned my phone calls and has always emailed me back. I have paid for a 1/8 scale boat in march. I was told 5 week i'am not mad nor bitter i realize some things take long then expected, and what i have seen from other peoples boats in my club...

don the trailer looks good to add more storage you can go between the floor joist and add boxes in the floor. I did this in my trailer and it works great. i use 16 gauge steel and bent it into a box on my metal break. my floor joist where 16" on center so i built my box 16 inches wide and 60...

I had the same thing happen to my short stroke nova rossi the bearing split in half and half stuck in the top of the piston and the other half stuck between the rod and the crank case. two different motors same day. i thought i was doing some thing wrong now i see someone else had the same problem.

Andy do i understand you correct that we can get parts for a short stroke nova rossi marine from the car guys. i have two short stroke nova that i need piston and sleeves.

hi guys i been reading this thread. has anyone ever tried to use the z-epoxy (45 min.) i was told to sand the hull with 220 then apply z-epoxy a thin layer with a disposable brush. then heat the epoxy with a hair dryer on low this makes the epoxy flow like water. whip off excess with the brush...

thanks for the advice but when i do that i come up .002 differance and i have tried many different combinations. I had new ones out on the bench because i have the aluminum shims and was checking to see if they were still good or if they have worn because the aluminum shims wear around the top...

i have lost my notes. I was checking the bearing and going through my twin ops 90 on my rigger and dropped the head shims. i have forgotten what the head clearance was. anyone have a general starting point. i use 50% nitro. stock ops 90 pipes. thanks for the help

I have been tring to find phil thomas (rc design marine web site could someone please list it or help me thanks. i would like to order a winston (lobster ) hull from him and a sport 40 hull.

yes sir the boat run fine when i put the old motro back in with the same needle and pipe. put the new motor in with a smaller prop an can not get it to run i can chage the motors backn forth if need be.

thanks for the info but the new 45 has only one hole not like the old disk type that has two and will put you out 180 if you don't have it right. also i check to make sure it did not start backwards

i just switched my ops .45 motor out in my rigger from the disk 45 to the new drum 45 both ops. i check the head clearance and set it to .009 i left the pipe from the old motor on the rigger set at the same pipe lenght. i have the same fuel and richen the motor to break it in, also put and a...

i seen this listing on ebay for futaba radio now is see it for mac motors and cmb is this guy trying to rip people off or is he a stand up guy? http://cgi.ebay.com/ws/eBayISAPI.dll?ViewI...5975377950&rd=1

MIKE IT IS A PINKERT CYCOTE. I WILL BUY IT IF YOU ARE GOING TO SELL IT I THINK IT IS TO HEAVY FOR YOU. I WILL GLADLY TAKE IT OFF YOUR HANDS.

talked to aero marine today they say they redesigned the crank and that he will contact ops to find out how to fit it to the old motor

mike if it is the old style i am interested mine has a crack in it where it connects to the rod. please email me a price and method of payment

i just received a new crank shaft for my ops 90 for aero marine i notice that the counter weight is smaller then the old one and the pin that goes into the rotor plate is larger. My question is did ops change the cranks and if so where can i buy the old style.

iam building an open cockpit but i was told r/c sportcraft makes a closed canopy for the pringles. i think the guys name is troy mcintryer