Octura 3/16" square drive ferrels - In search of ( 3/16" squared cable to 3/16" stub

[Mark Stein]

Anybody have any of these laying around they want to part with or can make them.
tia.

 

[FloridaScaleBoater]

Anybody have any of these laying around they want to part with or can make them.
tia.

Try Lenny Blake @ Rum Racing Products

 

[Daniel's Racing]

Again,

......and you'll be set for 4 more years. Lol.

https://www.intlwaters.com/threads/lf-wtb-3-16-square-drive.76418/

 

[Mark Stein]

Called Lenny but no luck for my type setup.
He does however carry a square drive setup.

 

[Mike Hughes]

MArk
I might have some. I will have to dig when I get home.
Mike

 

[Mark Stein]

Thanks Mike, fingers crossed

 

[shoboat]

Mark,

I think I still have some as well. I Will have to look tomorrow
when I get home from work.

Thanks,

Mark Sholund

 

[Timbo Whalen]

Anybody have any of these laying around they want to part with or can make them.
tia.

Mark, get hold of David Rippe at Hyperformance Products....great guy, high quality, reasonably priced rc boat equipment.

http://hyperprod.bizhosting.com/

 

[Mark Stein]

Timbo, I talked to Dave a few yrs ago. After a number of phone calls over 2 months. He was going to make them, then decided they were old school and wouldnt sell. I even offered to buy 20 that day before he made them, still no. Suprising is he still carries the 1/4" square ferrel.
I bought a new p Sport to build and have a few other boats to convert to dbl ended square drives.

 

[Mike Hughes]

Mark,
I dug deep. I have 3. Last of my stock. I think I have sold you some before. I am thinking 55 shipped.
Mike

 

[Mark Stein]

Thanks Mike, These would be the first I bought from you but I will take them.
Pm me with payment details

 

[Timbo Whalen]

Timbo, I talked to Dave a few yrs ago. After a number of phone calls over 2 months. He was going to make them, then decided they were old school and wouldnt sell. I even offered to buy 20 that day before he made them, still no. Suprising is he still carries the 1/4" square ferrel.
I bought a new p Sport to build and have a few other boats to convert to dbl ended square drives.

Mark, if all else fails, check with Offshore Electrics and Graves RC. Both places are well stocked with Octura components and specialty sourcing. Maybe you already know that.

 

[Mark Stein]

Wasnt aware of graves rc. Will check into it. This gets my current boats covered. But would like a couple spares.
I was going to make my own but couldnt find a resonably priced rotary broach with an mt2 taper
Even chinese ones were $400

 

[Timbo Whalen]

Wasnt aware of graves rc. Will check into it. This gets my current boats covered. But would like a couple spares.
I was going to make my own but couldnt find a resonably priced rotary broach with an mt2 taper
Even chinese ones were $400

https://gravesrc.com/

 

[Mike Betke]

Mecoa has them in stock

https://www.mecoa.biz/shopdisplayproducts.asp?catalogid=1086

 

[Mark Stein]

Thats the other end Mike

 

[John Beardslee]

Wasnt aware of graves rc. Will check into it. This gets my current boats covered. But would like a couple spares.
I was going to make my own but couldnt find a resonably priced rotary broach with an mt2 taper
Even chinese ones were $400

Mark
I used to make a single point tool for a mill (locked the head) and would broach out round holes to square using the quill feed like drilling but without the spinning. I would only do one side at a time. Did many key ways that way, I think it would work for a square drive.
John

 

[Mark Stein]

That I can probably do. I have a spin fixture I can set up for that. As long as it has 4 90 degree positions that. Kicking myself for not buying a lathe already