MTO sport 40's in IMPBA

[Don Ferrette]

How many people out there run the MTO round nose sport 40 in IMPBA?

 

[SayMikey]

How many people out there run the MTO round nose sport 40 in IMPBA?

I know Phil Thomas of all people has one and so does Bob Morton.

 

[P THOMAS]

Why do you ask this?

I just got one it is a bare hull still not setup.

I had a 40 roundnose built by a guy in MI but I wore it out :lol:

it was painted it up as Bardhal

https://www.intlwaters.com/gallery/thumbnails.php?album=287

 

[Don Ferrette]

Why do you ask this?I just got one it is a bare hull still not setup.

I had a 40 roundnose built by a guy in MI but I wore it out :lol:

it was painted it up as Bardhal

https://www.intlwaters.com/gallery/thumbnails.php?album=287

I got one over here to play with. Did you run it as made or change anything?

 

[boatr46]

where you get one?

 

[P THOMAS]

Why do you ask this?I just got one it is a bare hull still not setup.

I had a 40 roundnose built by a guy in MI but I wore it out :lol:

it was painted it up as Bardhal

<a href="https://www.intlwaters.com/gallery/thumbnails.php?album=287" target="_blank">https://www.intlwaters.com/gallery/thumbnails.php?album=287</a>

I got one over here to play with. Did you run it as made or change anything?

The Bardhal is not a MTO if you think that.

Just gotthe mto hull I have not set it up yet. Is your boat new or setup?

I was told put the motor as far foward as possible.

 

[Bob Morton]

Why do you ask this?I just got one it is a bare hull still not setup.

I had a 40 roundnose built by a guy in MI but I wore it out :lol:

it was painted it up as Bardhal

<a href="https://www.intlwaters.com/gallery/thumbnails.php?album=287" target="_blank">https://www.intlwaters.com/gallery/thumbnails.php?album=287</a>

I got one over here to play with. Did you run it as made or change anything?

Hey Don,

Do you or Phill or Mike have the steup sheet. That will help follow the directions

 

[Bob Morton]

Why do you ask this?I just got one it is a bare hull still not setup.

I had a 40 roundnose built by a guy in MI but I wore it out :lol:

it was painted it up as Bardhal

<a href="https://www.intlwaters.com/gallery/thumbnails.php?album=287" target="_blank">https://www.intlwaters.com/gallery/thumbnails.php?album=287</a>

I got one over here to play with. Did you run it as made or change anything?

The Bardhal is not a MTO if you think that.

Just gotthe mto hull I have not set it up yet. Is your boat new or setup?

I was told put the motor as far foward as possible.

Hey now Phill.

I have a Mac in it. From the plug to the transom it measures twenty two and a quarted inchs. With a motor that has a carb out front I would suggest getting to engine as far forwars as possible. (Picco,Cmb)

They are a blast and look great to

Bob

 

[P THOMAS]

Why do you ask this?I just got one it is a bare hull still not setup.

I had a 40 roundnose built by a guy in MI but I wore it out :lol:

it was painted it up as Bardhal

<a href="https://www.intlwaters.com/gallery/thumbnails.php?album=287" target="_blank">https://www.intlwaters.com/gallery/thumbnails.php?album=287</a>

I got one over here to play with. Did you run it as made or change anything?

Hey Don,

Do you or Phill or Mike have the steup sheet. That will help follow the directions

I dont have any setup info youhave a copy I could see?

 

[SayMikey]

Why do you ask this?I just got one it is a bare hull still not setup.

I had a 40 roundnose built by a guy in MI but I wore it out :lol:

it was painted it up as Bardhal

<a href="https://www.intlwaters.com/gallery/thumbnails.php?album=287" target="_blank">https://www.intlwaters.com/gallery/thumbnails.php?album=287</a>

I got one over here to play with. Did you run it as made or change anything?

Hey Don,

Do you or Phill or Mike have the steup sheet. That will help follow the directions

I dont have any setup info youhave a copy I could see?

I suggest you try to get the strut weight to less than 1/2 pound That might mean radio box and fuel tank up front.

 

[Bob Morton]

Why do you ask this?I just got one it is a bare hull still not setup.

I had a 40 roundnose built by a guy in MI but I wore it out :lol:

it was painted it up as Bardhal

<a href="https://www.intlwaters.com/gallery/thumbnails.php?album=287" target="_blank">https://www.intlwaters.com/gallery/thumbnails.php?album=287</a>

I got one over here to play with. Did you run it as made or change anything?

Hey Don,

Do you or Phill or Mike have the steup sheet. That will help follow the directions

I dont have any setup info youhave a copy I could see?

Phill

If I had one I would gladly give it to you. Maybe try Henry Valasco ???

 

[Jerry Muro]

Hey Don I know you said IMPBA but a guy in our District #1 NAMBA has been running one but had made some serious changes to the bottom from the end of sponsons to the transom he built it down 5/8's of an inch. He did this instead of adding weight to the front as per the directions I will check I think I still have the set up sheet from Doug DeWitt. I can tell you this the guy runs this with a Picco 45 and if he gets lane on as he usually does you wont even come close. The boat also hugs the bouys if you can believe that with a round nose. I will check tonight if I have them I can scan them and e-mail them to you. Jerry

 

[Bob Morton]

Hey Don I know you said IMPBA but a guy in our District #1 NAMBA has been running one but had made some serious changes to the bottom from the end of sponsons to the transom he built it down 5/8's of an inch. He did this instead of adding weight to the front as per the directions I will check I think I still have the set up sheet from Doug DeWitt. I can tell you this the guy runs this with a Picco 45 and if he gets lane on as he usually does you wont even come close. The boat also hugs the bouys if you can believe that with a round nose. I will check tonight if I have them I can scan them and e-mail them to you. Jerry

Hello Jerry,

I need to get together with you. So you can look this one over. I would also like to see the one you are talking about. Were are yinz guys racing at i just might take a ride :0 .

Also Lenny Blake from Rum Racing is making this hull. Maybe we can get Mike Shindler to make some.. They are a blast.

Bob

 

[Bob Morton]

Why do you ask this?I just got one it is a bare hull still not setup.

I had a 40 roundnose built by a guy in MI but I wore it out :lol:

it was painted it up as Bardhal

<a href="https://www.intlwaters.com/gallery/thumbnails.php?album=287" target="_blank">https://www.intlwaters.com/gallery/thumbnails.php?album=287</a>

I got one over here to play with. Did you run it as made or change anything?

Hey Don,

Do you or Phill or Mike have the steup sheet. That will help follow the directions

I dont have any setup info youhave a copy I could see?

Hey now Phill

Try Lenny Blake from Rum Racing

 

[Ray Sametz]

Mort's, talking it up, martini's must be flowing. :lol: :lol: :lol: :lol:

 

[Jerry Muro]

Hey Bob don't know about racing to much this year I am on a big job with alot of OT you know what I mean!!! Time and a half at GF rate. Cant pass that up. But Joe and I are going to try to attend at the District 12 gas race in July. Heard alot about the crabs and Martinis!!! Talk to you soon Jerry

 

[Bob Morton]

Hey Bob don't know about racing to much this year I am on a big job with alot of OT you know what I mean!!! Time and a half at GF rate. Cant pass that up. But Joe and I are going to try to attend at the District 12 gas race in July. Heard alot about the crabs and Martinis!!! Talk to you soon Jerry

We are going tooooo. First martini is on me