Julians rigger @ Brandon

[Speed Jr.]

H-32's? Come on, Id sure hope you could pull stock 1667's as a base prop. Julian, is that Ron Zaker's old boat?

Jr.

 

[shoboat]

Larry & Others,

An ABC H-48 is really just a reduced 1667 @ aprox. 64mm.

The H-32 has just a little less blade area so it loads the

engine less. I would start working on the turnfin so the boat

handles a little better. The right side motor looks lean, do you

have a digital temperature gauge handy?

Julian,

I have a set of H-32's that you can test if you would like?

They are a matched set @ 5.29" of cup and 4.29" center of blade pitch.

Shoot me your address and I will send them down to you.

Keep Testing,

Mark Sholund

231.590.3023

 

[Tom Foley]

Larry & Others,

An ABC H-48 is really just a reduced 1667 @ aprox. 64mm.

The H-32 has just a little less blade area so it loads the

engine less. I would start working on the turnfin so the boat

handles a little better. The right side motor looks lean, do you

have a digital temperature gauge handy?

Julian,

I have a set of H-32's that you can test if you would like?

They are a matched set @ 5.29" of cup and 4.29" center of blade pitch.

Shoot me your address and I will send them down to you.

Keep Testing,

Mark Sholund

231.590.3023

Guys , just bear in mind that this was just a (literally ) thrown together test and one engines bearings were really crappy . The hull was FUBAR in terms of setup and Ralph is now setting up the boat for Julian . I have both engines apart waiting on bearings and will de - flash the chrome on the liners , match the ports , re- bearing and clean up a few things in the radio box . The pistons and sleeves and cranks etc are basically new .This boat will be a friggin missle once these engines are in harmony ..then its up to Julian not to run into stuff !!!

 

[julianconde]

Larry & Others,

An ABC H-48 is really just a reduced 1667 @ aprox. 64mm.

The H-32 has just a little less blade area so it loads the

engine less. I would start working on the turnfin so the boat

handles a little better. The right side motor looks lean, do you

have a digital temperature gauge handy?

Julian,

I have a set of H-32's that you can test if you would like?

They are a matched set @ 5.29" of cup and 4.29" center of blade pitch.

Shoot me your address and I will send them down to you.

Keep Testing,

Mark Sholund

231.590.3023

**the H 48's runs really well. my H667 are better but i snaped a collet and the pond gods took the shaft and prop.

**Yes this was Ron Zakers Twin.

**I have a set of 1667 that i will pick up from a friend and test on my boat Ralph (Mr. Roadrunner) will be there also to ensure everything goes well with the boat.

**Mark ill test the props address posted below..

**The problem with the boat was that it was not set up at all needs some work .when i got it from Ron Zaker we havce seen some stuff that needs to be fixed but we are working on that tomorrow. Hopefully i can get this boat running like it should if not i have to go back to the drawing board with it.

julian conde

436 carter Rd

Clarksville TN 37042

 

[shoboat]

Julian,

If you have the numbers on the H-667 I will send you another one.

I am just trying to help you with your set up. Nice looking boat

on the water. If you bend the tips down on the 48's it will help

the roostertail just drop into the water. Nice camera work, and it

sure is nice to watch on film.

Thanks,

Mark Sholund

 

[julianconde]

i will send you the numbers tomorrow i dont have the cards here with me ok. I appreaciate your help my friend thank you your props are awesome..

julian

 

[Buckshot]

Julian,

I like your choice in hats.



B

 

[FloridaScaleBoater]

Larry & Others,

An ABC H-48 is really just a reduced 1667 @ aprox. 64mm.

The H-32 has just a little less blade area so it loads the

engine less. I would start working on the turnfin so the boat

handles a little better. The right side motor looks lean, do you

have a digital temperature gauge handy?

Julian,

I have a set of H-32's that you can test if you would like?

They are a matched set @ 5.29" of cup and 4.29" center of blade pitch.

Shoot me your address and I will send them down to you.

Keep Testing,

Mark Sholund

231.590.3023

**the H 48's runs really well. my H667 are better but i snaped a collet and the pond gods took the shaft and prop.

**Yes this was Ron Zakers Twin.

**I have a set of 1667 that i will pick up from a friend and test on my boat Ralph (Mr. Roadrunner) will be there also to ensure everything goes well with the boat.

**Mark ill test the props address posted below..

**The problem with the boat was that it was not set up at all needs some work .when i got it from Ron Zaker we havce seen some stuff that needs to be fixed but we are working on that tomorrow. Hopefully i can get this boat running like it should if not i have to go back to the drawing board with it.

julian conde

436 carter Rd

Clarksville TN 37042

Julian,

You have some of the best in our hobby helping you out buddy,

I don't know how tom does it, being spread so thin, with so many boats that he runs,,,, But EVERYTHING he has runs great!!!

With an army like that, I'm sure yours will be running great real soon.

Hope to se you in Huntsville in April/May

 

[julianconde]

I'll be at Huntsville for sure. Thanks Buck like I say don't mess with TX

 

[julianconde]

Well the sponsons have been fixed and set up by Ralph and now all that's left is the engines bearings by Tom then back to the pond we go will keep you guys posted.

Julian

 

[julianconde]

Twin is ready and going to the pond tomorrow we will see whats up hopefully it all goes well..

julian

 

[RaceCraftBearings]

Made some modifications to my F Boat, will be there to see what I have.

 

[julianconde]

thats awesome that will be great

julian

 

[RaceCraftBearings]

Loaded up and ready to roll to the Brandon Lake............

 

[julianconde]

Same here I'm on my way there.

Julian

 

[robertpickard]

Ron arent you getting ahead of yourself the race is in March see you in a couple weeks.

 

[dwilfong]

Well how did it go guys.

 

[RaceCraftBearings]

Well how did it go guys.

No Robert its a play day

Went pretty good David, 20 Hydro is a rocket and the 90 Hydro shows signs of improvement. Made my rear booms adjustable shimmed it up a bit, shortend my pipe to 11-1/8 added a bit of pitch to that 1667, took the cup out and it ran the best I have seen it until the fuel load got low then it began to hop. My fuel load is way more than I need for mill and 6 laps of racing so I probably will be good there. May shim the rear boom tube up a tad bit more.

Made fun of Julians trailer tires with no tread knowing I have plenty but guess who had blowout half way home LOL!

I did

 

[julianconde]

Well my nitro twin ran extremely well. It rides and turns food now we have to get the engines working together an the boat is ready for racing. My 20 hydro ran good but a bit slow but it will do. Go Fast Foley tried to outruning my twin gas catamaran we had some good cat racing that makes it 3-3 Foley.

I wanna thank Ralph (Roadrunner) for the boat set up and Go Fast Foley for puting the new bearings on my twin.

Had a great time with Andy Green and Ron Byrd and Ron Drake plus Randy Premo.

It was great comming up here to Brandon looking foward to comming back very soon.

Thanks

Julian Conde

 

[Tom Foley]

Gimme a holler Biotch if you want to come up toi the suwannee River this weekend and go for as real boat ride and big bonfire ..heading up Friday afternoon/ night . we will revisit the Cat Race !! Your Twin nitro rigger is looking good , some good props and a little Mo Jo and you are in the saddle !