ShockWave 36 Nitro Boat
Like stated above, its a ShockWave 36 nitro powered r/c boat.
This was 1 of the boats in my 7 boat fleet. Had alot of fun with this boat.
It proved to be the most reliable boat i had out of the 7 boats i owned.
I dont NEED to sell this boat, but it has been sitting around collecting dust.
So i guess its time for it to go.
The boat is produced by Pro Boat, it is in pretty good shape.
Comes with alot of extras, needs some minor TLC.
Boat is hopped up pretty nicely.
What all is included-
14.8 ounces of fiberglass resin(brand new)
Extreme Power 30 minute epoxy which is about 2/3 gone
Bottle of after run oil and a surenge
Hatch tape for taping down the radio box lid
Z bender pliars by Hanger 9 for bending "Z"'s in linkage wire
2 Hobbico hot shot 2 glo igniters, 1 ni starter glow igniter
1 Traxxas 2018 servo, 1 TowerPro MG995 servo(brand new), 1 JR DS821 servo(brand new)
Spare rudder stand off bracket
Spare flex cable with prop shaft
Cannister of Prather cable grease
Bottle of Graphite lube (brand new)
Spare engine mounts
Stock Header
2 brand new Axe Rossi r$ glow plugs
4 6 volt receiver packs. 1 1100mah pack and 3 1600mah packs
Spare Octura X646 prop
Plenty of servo horns
Bag of linkage collars
Spare exhaust pieces
Several pieces of spare linkage rod, all brand new
Gallon and a half of 30% nitro by Tilted R/C(May not be able to ship this)
Kyosho Tool Bag, holds SEVERAL tools(brand new)
The hardware on the boat has all been polished.
ive got about $60 wrapped up in the rudder and rudder stand off bracket.
Boat has been wrecked one time. It was nothing too serious. Boat was repaired
sucesfully and ran several more times after the incident.
The stock JR Python radio is included. The boat comes with a Dynamite .32
nitro engine. The engine does need to be rebuilt. I can rebuild it for you if you
buy the parts, no problem. The Dyanmite .32 was modded. Boat would run in the high
40's with the Octura x646 prop which was sharpened, balanced and polished. This boat
use to handle like it was on rails. Spent alot of time hopping up and improving this boat, along with
many hours out on the water enjoying this boat.
great boat for a begginer, and also a great boat for an experienced user.
Ive owned this boat for about 2 years now, i've had it since it was new.
I took great care of the boat. Always performed the after run procedures on the boat.
Always dried it off after a run on the water. The engine needs a new piston and sleeve.
You can either replace the piston in sleeve or just buy a brand new motor for around $90.
The Dynamite .32 motors are pretty cheap. So just buying a new one would not be a bad idea at all. Boat has got some very minor scratches on the bottom of the boat. Mostly from driving the boat back to shore and idling through mud or a sand bar.
I would like to get $95 for everything pictured. I will go half and half on the shipping costs also.
You can see a few more pictures by viewing the following links-
More info on this boat from the dealer-
http://www.horizonhobby.com/Products/Defau...ProdID=PRB2050T
If you have any questions or your interested in my boat. Feel free to give me a call at 217-299-8600 or you can also just PM me or reply here.
Thanks!
Like stated above, its a ShockWave 36 nitro powered r/c boat.
This was 1 of the boats in my 7 boat fleet. Had alot of fun with this boat.
It proved to be the most reliable boat i had out of the 7 boats i owned.
I dont NEED to sell this boat, but it has been sitting around collecting dust.
So i guess its time for it to go.
The boat is produced by Pro Boat, it is in pretty good shape.
Comes with alot of extras, needs some minor TLC.
Boat is hopped up pretty nicely.
What all is included-
14.8 ounces of fiberglass resin(brand new)
Extreme Power 30 minute epoxy which is about 2/3 gone
Bottle of after run oil and a surenge
Hatch tape for taping down the radio box lid
Z bender pliars by Hanger 9 for bending "Z"'s in linkage wire
2 Hobbico hot shot 2 glo igniters, 1 ni starter glow igniter
1 Traxxas 2018 servo, 1 TowerPro MG995 servo(brand new), 1 JR DS821 servo(brand new)
Spare rudder stand off bracket
Spare flex cable with prop shaft
Cannister of Prather cable grease
Bottle of Graphite lube (brand new)
Spare engine mounts
Stock Header
2 brand new Axe Rossi r$ glow plugs
4 6 volt receiver packs. 1 1100mah pack and 3 1600mah packs
Spare Octura X646 prop
Plenty of servo horns
Bag of linkage collars
Spare exhaust pieces
Several pieces of spare linkage rod, all brand new
Gallon and a half of 30% nitro by Tilted R/C(May not be able to ship this)
Kyosho Tool Bag, holds SEVERAL tools(brand new)
The hardware on the boat has all been polished.
ive got about $60 wrapped up in the rudder and rudder stand off bracket.
Boat has been wrecked one time. It was nothing too serious. Boat was repaired
sucesfully and ran several more times after the incident.
The stock JR Python radio is included. The boat comes with a Dynamite .32
nitro engine. The engine does need to be rebuilt. I can rebuild it for you if you
buy the parts, no problem. The Dyanmite .32 was modded. Boat would run in the high
40's with the Octura x646 prop which was sharpened, balanced and polished. This boat
use to handle like it was on rails. Spent alot of time hopping up and improving this boat, along with
many hours out on the water enjoying this boat.
great boat for a begginer, and also a great boat for an experienced user.
Ive owned this boat for about 2 years now, i've had it since it was new.
I took great care of the boat. Always performed the after run procedures on the boat.
Always dried it off after a run on the water. The engine needs a new piston and sleeve.
You can either replace the piston in sleeve or just buy a brand new motor for around $90.
The Dynamite .32 motors are pretty cheap. So just buying a new one would not be a bad idea at all. Boat has got some very minor scratches on the bottom of the boat. Mostly from driving the boat back to shore and idling through mud or a sand bar.
I would like to get $95 for everything pictured. I will go half and half on the shipping costs also.
You can see a few more pictures by viewing the following links-
More info on this boat from the dealer-
http://www.horizonhobby.com/Products/Defau...ProdID=PRB2050T
If you have any questions or your interested in my boat. Feel free to give me a call at 217-299-8600 or you can also just PM me or reply here.
Thanks!
