Eagle sg

[Roxyflash]

So Adam has this eagle sg it’s 41 inch long tub.Supposedly **** Jones had this boat built to his specs.Im going to rebuild it she’s in rough shape.Looks like when it was first built had two rear ride pads.Then there’s a center shoe added as it’s in wood grain and out ride pads are painted.Its going to need a new cowl and rudder assembly to start with.Its this boat a 80 boat?

 

[ALLAN YUEN]

Yes It built in for 80 engine

 

[Roxyflash]

Does anyone know the size of the rubber grommets for the engine bolts these are totally worn out.

 

[John Beardslee]

I think they are 1/4” ID x 7/16” OD for a 1/4” panel

 

[John Beardslee]

You’ll want the stiffer rubber if available. ie: higher durometer or shore number.

 

[Roxyflash]

Thanks will take a look for them

 

[Timbo Whalen]

Does anyone know the size of the rubber grommets for the engine bolts these are totally worn out.

I may be able to help you with the grommets....measure hull side thickness, mounting screw OD- both head and threaded diameters- and hole diameter in tub. I've a bunch of them for different size hydros, all new from M-C, fuelproof and correct durometer.
If I've the right size, I'll just send you some.

 

[Roxyflash]

Timbo here’s what I got tub side wall thickness is 1/4 inch hole size in tub is 13/32 but there’s paint in the holes bolt size is 1/4 inch I found one new grommet the middle outside measured. About .425 that’s where it fits into the hole if you don’t have them no big deal as I found one new one that’s not mushed out.

 

[Timbo Whalen]

Timbo here’s what I got tub side wall thickness is 1/4 inch hole size in tub is 13/32 but there’s paint in the holes bolt size is 1/4 inch I found one new grommet the middle outside measured. About .425 that’s where it fits into the hole if you don’t have them no big deal as I found one new one that’s not mushed out.

Ok, give me a day, or two....all my fastener stuff is in storage....quite certain I have them.

 

[Roxyflash]

Sounds good next few days going to aircraft strip the paint off.Got the hardware out of the hull had a hell of time getting the strut and drive shaft tube out of stuffing box.The hull must of had a drum style motor then later on had a disk motor the stuffing box was extended and soldered along with the flex shaft tube so I tried a soldering gun but couldn’t get it all heated so had to resort to a mini torch.By the time I got it freed the ski on on the bottom was pealing off so I ended up resheeting the ski.I also rebuilt the stuffing box and reinforced it so now you can slide the the flex shaft tube in and out.The tub had the plastic pushrod mounts glued in I drilled them out install woods pushrod mounts.Heres a couple pictures.

 

[Timbo Whalen]

Sounds good next few days going to aircraft strip the paint off.Got the hardware out of the hull had a hell of time getting the strut and drive shaft tube out of stuffing box.The hull must of had a drum style motor then later on had a disk motor the stuffing box was extended and soldered along with the flex shaft tube so I tried a soldering gun but couldn’t get it all heated so had to resort to a mini torch.By the time I got it freed the ski on on the bottom was pealing off so I ended up resheeting the ski.I also rebuilt the stuffing box and reinforced it so now you can slide the the flex shaft tube in and out.The tub had the plastic pushrod mounts glued in I drilled them out install woods pushrod mounts.Heres a couple pictures.

My apologies.....the biggest I have right now are for .187" thk panel, .187" ID......

However, here's what you need-

https://www.mcmaster.com/9307K39/

 

[Roxyflash]

Thanks for looking those must be for a 21 boat

 

[Timbo Whalen]

Thanks for looking those must be for a 21 boat

No, 45/67

 

[Roxyflash]

Found the grommets same size as a ceiling fan blade grommet.Stripped the boat needs a final sanding before I epoxy seal it.filled a few imperfections with wood putty.Adam ordered some cowls from Phil Thomas.Fitted it to the tub but was a 1/4 short in the tongue in front so I glued a 1/4 strip of g10 to fill the gap I also cut two pieces for radio box lid and bait box lid.Heres a few pictures.

 

[Rich Jones]

That’s a lot of work. You make it look easy!

 

[Roxyflash]

Wasn’t easy I thought I was done rebuilding for the winter then Adam shows up with this project being **** Jones old boat I wanted it nice and the right way was to gut it and strip it custom mounts for speedmaster hardware milled and mounted the engine strip the hull rebuild stuffing box new cowl and fit it.Been a busy two weeks.

 

[Roxyflash]

Temp was good today windy but doable.Want this project done.I found some old Imron paint from my daughters 20 eagle medium blue matches Adam ram truck he really like the color so I painted the sponsons cowl radio and bait box lids.Painted the tub orange.Hard to believe the date code on imron was 2001

 

[Rich Jones]

Temp was good today windy but doable.Want this project done.I found some old Imron paint from my daughters 20 eagle medium blue matches Adam ram truck he really like the color so I painted the sponsons cowl radio and bait box lids.Painted the tub orange.Hard to believe the date code on imron was 2001

Wow that stuff must have been in a cool dry place! Looks good!

 

[Roxyflash]

Here’s the eagle sg 21 from 2001 the paint has been in the basement on the top shelf found it two weeks ago I was happy it turned out I started on the lids and was happy

 

[Rich Jones]

Here’s the eagle sg 21 from 2001 the paint has been in the basement on the top shelf found it two weeks ago I was happy it turned out I started on the lids and was happy

Hard to believe 2001 was 23 years ago. Where does time go?