Christmas is time for giving!

[FloridaScaleBoater]

i have a tower hobbies deluxe starter to give away... brand new never used but missing the rubber insert for o/b's.... free to who ever wants it... throw me a addy and its on its way...

merry xmas

alden

I'll take it Alden, thanks!!

John

Dangit, I need one of those, for the new tunnel I aquired.

was holding off till after the holiday's

Rick

 

[Bob Howard]

Here is an old CMB .45, Bearings are rough, flywheel missing, good compression. Merry Christmas

Bob

 

[Andy Greene]

i have a tower hobbies deluxe starter to give away... brand new never used but missing the rubber insert for o/b's.... free to who ever wants it... throw me a addy and its on its way...

merry xmas

alden

I'll take it Alden, thanks!!

John

Dangit, I need one of those, for the new tunnel I aquired.

was holding off till after the holiday's

Rick

Im pretty sure I have one- let me look Rick....

Geeze , ME giving stuff to the grinch- go figure

 

[Bill Gibson]

i have a tower hobbies deluxe starter to give away... brand new never used but missing the rubber insert for o/b's.... free to who ever wants it... throw me a addy and its on its way...

merry xmas

alden

I'll take it Alden, thanks!!

John

Dangit, I need one of those, for the new tunnel I aquired.

was holding off till after the holiday's

Rick

Im pretty sure I have one- let me look Rick....

Geeze , ME giving stuff to the grinch- go figure

Andy,if you dont, ill do some lookin in my shop....i MIGHT have a standard 12 volt Sullivan layin around which will EASILY start an outboard for the OL GEEZER! (You are 50+ now...arent you Rick?? :lol: :lol:

 

[bzubee]

Thank you Dan

Bill, its yours.

send me a PM with your full address.

Dan.

 

[Andy Greene]

Hey grinch-

I found the starter you need-

but its gonna cost ya

No grief for 1 year- LMAO

If you dont wanna eat crow for a year-

I found ya this(post 188) :lol: :lol: :lol:

http://www.jrcbd.com/showthread.php?t=34039&page=19

Im a little behind sending the stuff out so far(sorry guys) but I have had steady work and at this time of year I have to run with it.

Andy

 

[M@MRacing]

Bill and Andy i have a starter here Rick can have in good condition

 

[Bob Howard]

Here is an old CMB .45, Bearings are rough, flywheel missing, good compression. Merry Christmas

Bob

Sending to roxyflash

 

[chris1088]

I have a 3.5 picco pipe let me know

 

[opio]

lol I should grab that pipe for the motor lol! nah I have got enough from this thread! lol

 

[camaroboy383]

john,,,(fishinghole) the starter is yours,,, i sent you a pm...

alden

 

[Andy Greene]

Bill and Andy i have a starter here Rick can have in good condition

Good then take care of Grinchmas

I dont wanna have to hear him crying about eating crow........

 

[larcor69]

Hey Chris if that pipe aint cut to short I really need it, Thanks..Corey

Also to everyone I still have a brand new standard JR servo???

 

[chris1088]

Hey Chris if that pipe aint cut to short I really need it, Thanks..Corey

Also to everyone I still have a brand new standard JR servo???

It is 4 1/2 center 8 1/2 totol let me know

 

[larcor69]

that should work with a 31/2 header, I will take it if still availble PM sent

 

[chris1088]

that should work with a 31/2 header, I will take it if still availble PM sent

Happy Holidays it is yours !!!

 

[bzubee]

Ron your nuts are in the mail should be at Mike's by Christmas Eve. Merry Christmas

 

[FloridaScaleBoater]

Bill and Andy i have a starter here Rick can have in good condition

Thanks guy's I'll hit Robert up for this one.

Thank you

BTW Robert, Getting close to needing paint

 

[Dan Hydro]

Bill,

your carb is in the Mail.

Be patient with the mail system. Have a good X-Mas and Happy new year.

Dan.

 

[bzubee]

Back at you ! Thanks again.

Bill,

your carb is in the Mail.

Be patient with the mail system. Have a good X-Mas and Happy new year.

Dan.