BAD DAY AT THE POND

[dwilfong]

Well I was pulling 7.5" of prop at 10 1/4 " of pipe and the boat hooked and stooped.

This is what I found when it got back to shore.

Like I said if you aren't pushing the edge you are just going around in circles.

David

 

[SayMikey]

Well I was pulling 7.5" of prop at 10 1/4 " of pipe and the boat hooked and stooped.

This is what I found when it got back to shore.

Like I said if you aren't pushing the edge you are just going around in circles.

David

OUCH Elam takes a hit

 

[julianconde]

dam Jumper needs some repairs.

julian

 

[TimothyJones]

Have had that happen twice.

Tim

Well I was pulling 7.5" of prop at 10 1/4 " of pipe and the boat hooked and stooped.

This is what I found when it got back to shore.

Like I said if you aren't pushing the edge you are just going around in circles.

David

 

[brett english]

Well I was pulling 7.5" of prop at 10 1/4 " of pipe and the boat hooked and stooped.

This is what I found when it got back to shore.

Like I said if you aren't pushing the edge you are just going around in circles.

David

David was that prop heat treated?? what prop was that?

 

[Ken Webb]

Looks like you hit something in the pond.

 

[Kevin Krogness]

Little elmers can fix that right up

 

[Brian Sorgente]

Pic 1: Bill Longely pulling his cat ... well, out of another cat lol.

Pic 2: Early on when I first got into boating, my .90 avenger spider went out of control and met the the outdrive of a full sized inboard on the lake. Luckily for me, that was all it hit. I learned a lot from that boat :lol:

 

[Andy Greene]

There was some today at Riverview- but I couldnt bring myself to take a shot of it- Lets just say Winton's gas rigger needs some tlc

I have a pretty cool one of Byrd pulling Perry's scale boat out of my of Circus hull before I got it from Mike, will post it up.

 

[Andy Greene]

Here ya go -

 

[ALLAN YUEN]

Well I was pulling 7.5" of prop at 10 1/4 " of pipe and the boat hooked and stooped.

This is what I found when it got back to shore.

Like I said if you aren't pushing the edge you are just going around in circles.

David

:blink: Too much 7.5" cup so around in circle( like spin) then out of control cause your fin turn was negative low Must change adjust on boom tubes or turn fin

 

[dwilfong]

Well I was pulling 7.5" of prop at 10 1/4 " of pipe and the boat hooked and stooped.

This is what I found when it got back to shore.

Like I said if you aren't pushing the edge you are just going around in circles.

David

David was that prop heat treated?? what prop was that?

no it was not. Thought I would just test with it before the heat treatment. WRONG!!!!!!

Next one will be done before I run it.

Top secret new prop can't say right now. Lets gust say it's got 6" COB and 7.5 TE and I need more!

My 91RS didn't even know it was there. :lol:

Can you say 90+MPH around the corner.

Have a local cop joining the club. Had his cruiser there to day with radar in it. Going to park it on the front stretch next time and see what it dose.

The new eng set up is right on the money. just need more time to test.

David

 

[dwilfong]

Well I was pulling 7.5" of prop at 10 1/4 " of pipe and the boat hooked and stooped.

This is what I found when it got back to shore.

Like I said if you aren't pushing the edge you are just going around in circles.

David

:blink: Too much 7.5" cup so around in circle( like spin) then out of control cause your fin turn was negative low Must change adjust on boom tubes or turn fin

It did it in the middle of the back straight at full tilt. The prop broke a blade off.

It runs real good in the corners shimmed up the rear boom tubes to tighten it up already.

David

 

[julianconde]

better get JUMPER ready for brandon my friend

julian

 

[dwilfong]

better get JUMPER ready for brandon my friend

julian

Don't think It will make this one.

But then again you never know.

David

 

[Andy Greene]

better get JUMPER ready for brandon my friend

julian

Load up that other ModVP - I need it

 

[julianconde]

that Mod VP dont exist anymore Mark Poole has it right now

 

[shoboat]

David,

I guess we will have to make that one in Stainless Steel Huh?

It looks like we have to add just a little more, and next time it

should fly right over that GATOR.

I'll have another one ready just beef up that transom.

I think JUMPER has a new name?

Bummer,

Mark Sholund

 

[dwilfong]

David,

I guess we will have to make that one in Stainless Steel Huh?

It looks like we have to add just a little more, and next time it

should fly right over that GATOR.

I'll have another one ready just beef up that transom.

I think JUMPER has a new name?

Bummer,

Mark Sholund

Mark got the transom all fixed.

I'm ready let slap some more prop to it.

David

 

[shoboat]

David,

Not a problem.

I have another already started.

Thanks For Testing It,

Mark Sholund