Search results

I don't know why it didn't work.I have tried various setup on the Top Speed2 and its just doesn't get on speed and the turning is terrible.All the while I thought is the Rossi doesn't give the performance as claimed.I was about to give up on the engine and finally just mount it on the K&B lower...

Its a bullet drive from hyperprod.I got the angle drive from them and its a big disspointment.Since I live so far away from U.S I dare not try anymore lower unit except K&B lower.Its a 4 bolt powerhead.Fit directly into the K&B lower.

Pulsetech its good to hear you bought another TS2 and please tell us on how it run compare to the previous one you had.I didn't manage to get any over here but I bought a Bristol Bay by Aquacraft.Hope to hear on the outcome of your new TS2

Russ, thanks for the offer on replacement.As what pulsetech said the cost of shipping itself is going to cost a bomb.You don't have to be sorry about it as I understand the hull are mass produce and will have some problem here and there. I really appreciate it when you admit the problem on the...

Ok Moron (hope you don't mind) I don't mind telling thats what I did as the last resort and it doesn't make any difference to the way it run and the handling is worse.I was just hoping it will get up on speed and don't really care about the handling.At least I can make a tight turn evendo it...

Moron maybe you or anyone an give some advise for the remaining guys over here on how to make their TS2 run like the video in Aquacraft website. Jerry Dunlap - as you mention on the floor of the hull should be flat,I would check mine and let you know,and beside the floor what are the other...

Pulsetech I have try everything to make this hull run,I have already given up on it after numerous setup,engine and also modification.In fact there is only one or two are running over here and the rest have already put it back in the box.There is one guy bought and only look at the manual only...

Pulsetech your boat really bounce very badly. I have never seen any TS2 bounce as bad as yours.At least my problem is it does not plane.Now I truly understand your problem and also your frustation.What I notice at certain point when you gun the throttle it goes quite fast.I believe your problem...

Thanks for all the help guys, I have glue a polycarbonate plate under the sponson and now the edge is really square and hope it will work.Pulsetech might be right after you mention it that it might be cavitating.The engine peaks easily and the boat hardly move.It sounds like the prop is...

Pulsetech I hope you method will work for me as well,but my primary objective is to glue the polycarbonate plate under the sponson which I have just purchase.Will keep you update on how it goes.When my boat run,what I have notice is almost the whole engine submerge in the water and i am really...

Well I think I have gone through what Pulsetech did and as I mention earlier in my post.My problem is the boat doesn't plane.I did try adjusting the prop height and also the angle doesn't make any diference.Correct me if I am wrong after what I notice yesterday after looking at the hull for 3...

Thank you for all the advise,I still haven't given up hope on this hull yet,by the way i forgot to inform that the rossi is still new and its was only running on the 3rd tank of nitro,do any of you think is still running in or the opposite? Currently I haveonly run it on a Prather 215 prop...

Jerry or anyone who have successfully run the TS2, I am badly in need of help here, over heremost of the guys who run the TS2 have given up on it. I have try to run it with a TT and to the extend purchase a rossi from hyperprod bolted on angle drive t my dissapointment it doesn't make any...

Its a 3.5cc outboard powerhead. :)

I would like to know what is the best way to run in this engine? Should I just run it in the water or just put it on the rich side and leave it on the ground?How many turn of the needle for running in. I hope the Rossi guru will give me a few opinion on this.

I manage to spoke to David from Hyperfomance Products today.Actually there are out of town and only back yesterday. Called Gary from G&M too and he only carry K&B.

Thanks Lohring for the information,anyway I will wait till after new year.Happy New Year.

I emailed to them a couple of days ago to inquire a few products.Till todayhaven't got any reply.I was wondering is it still a holiday in U.S or they have a policy of not replying for shipping outside U.S? Can anyone please help me to suggest a better hobby shop which supply outboard power head...