Search results

Intlwaters

Help Support Intlwaters:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. TomGracey

    Your First 50 mph/or Faster Patch

    Sorry that the only pic I have that boat was from the 1960-70s Era
  2. TomGracey

    End Mill Suggestions

    https://littlemachineshop.com/products/product_category.php?category=-1180321415&First=E&Last=E
  3. TomGracey

    Your First 50 mph/or Faster Patch

    When I was finished with all the bottom skins just getting ready to start on the decks Ron stop by my place to pickup some some Con. Rods I machined out of 7075 T-6 (the stock OPS rods were cast Aul. and broke easily) I digress he pick the hull off the jig and said if U want this to ride right...
  4. TomGracey

    Your First 50 mph/or Faster Patch

    My 50+ club was in 1966 with S.M.Y.C. Hull was a Dumas Dragn Fli 60 and a Ron Ericson built OPS 60 side exhaust throttle on 60% and a Ronny Racer Prop
  5. TomGracey

    Waterproof Receivers

    Its easy to waterproof any RX or other electronics . Remove the circuit board from the case. Protect the plug pins with some small tubing or heat shrink . Brush on 2-3 coats of the Silicon Conformal coating allow to dry between coats reassembly. Apply a small amount of Silicon grease to the...
  6. TomGracey

    WTB OPS .67 pipe TNX Found 1

    Looking for a OPS.67 PN# 6280 pipe must be in very good condition Please no junkers
  7. TomGracey

    Nova Rossi car engine for .20 hydro........

    https://www.novarossi.us/products/marine-inboard-and-outboard-flywheels?variant=9403490371
  8. TomGracey

    Finished: M L's 1/6 Gas Scale "Winston Eagle Lobster"

    Nice build wish mine was that far along but it's getting closer getting closer
  9. TomGracey

    JD Builds a Foam 1/10 Scale 8255

    Is that 1914 45R a raw casting or sharpened thinned & balanced ???
  10. TomGracey

    ESC MHA ratinng

    What would be the minimum reliable mAh rating for a ESC in a 1/10 th Scale Hydro running a Himax HB3630 1500 Kv brush-less – 6 pole brush-less with a 4s 6000 mAh 20C lipo. The reason I'm asking is I have a ZTW Seal 130 A/ 2-6s lipo ESC but space in the Engine well is tight and I'm having...
  11. TomGracey

    Andy Brown

    Anyone have contact info for Andy Brown RC Boat Racing Propellers my present bookmark says it can't find his website
  12. TomGracey

    Looking for club or pond near Vancouver Washington

    This might help NAMBA District 8 website http://namba8.com/wp/?fbclid=IwAR1Fb-Kt2aOawl8bQJhvupUWFaAQT8Y7qzsgZMzsWORuTRZADxbGOc51QDg
  13. TomGracey

    FS Sullivan Deluxe Hi-Tork /Hi Rpm starter

    New Never Used Sullivan Deluxe Hi-Tork /Hi Rpm starter Stock No. 6-1 code HD This item is surplus to my needs Purchased as part of a lot sale during a going out of Business sale a few years ago (Performance Hobby’s formally in Burlington Wa.) New Retail $99.94 Asking $70.00 Firm shipped to the...
  14. TomGracey

    FS Rossi .67 TO-BE Direct Drive Marine Engine

    For Sale .67 TO-BE Direct Drive Marine Engine w/ Rear Exhaust with the latest updated Connecting Rod plus new Cylinder and Piston & ,Bearings , Header’s, Tuned Pipe, a floor-mount engine mount & flex Shaft collet. Has not been run since latest updated Connecting Rod new Cylinder and Piston...
  15. TomGracey

    For Sale - New Novarossi 91 with modifications

    That might explain why my .67 To-Be Top through a rod taking the Cylinder and Piston out 5 min's in to it's initial run on a new engine .:mad:
  16. TomGracey

    For Sale - New Novarossi 91 with modifications

    If You watch this Video on how the Rossi FACTORY breaks in an engine It'll scare the crap of of Ya , Its closer to DESTRUCTIVE TESTING
  17. TomGracey

    Engine Mounts

    Does anyone Know if the CMB .21 Beta and Rossi .21 Keep Direct. Drive Marine Engine's w/ Rear Exhaust have the same engine mount bolt hole pattern .
  18. TomGracey

    ML Boatworks- Vision 20 and 40 Tunnels are back! Molds just arrived.

    Nice I see a purchase in the near future I noticed that the lower front of the cowl is open how does it connect to the hull.
  19. TomGracey

    Sport 20 Engines

    I'v always been a CMB guy Have a Rossi. 21 on a B mod tunnel hull. The 1 Rossi .67 Top I had in my old Bud T-6 through a rod twice taking out the liner and piston But in back together with the latest updated rod, piston and liner and sold it off. I even had the crank balanced after the 1st...
Back
Top