Search results

Ive got 2 12mm mac carbs , looking for a 14mm

Just noticed around the world the cmb hr90 is dead , and reason why ? Removed everywhere

ok guys ... with that pipe length , what % nitro are you running , what plugs are running well , and what props can it turn, in a jae 12? many thanks jason

are you using a spectrum radio gil ? jason

nice boats these jase

charge it at 1c ,or 2c if your in a hurry (to run a race) ... fast charging will limit the packs useful life . also , while many chargers will charge at 10-25amps , the problem is NONE of them balance a pack properly at that rate . look into how fast your charger can balance charge , and...

+1 on this for sure !! leo 3674 - 3000kv-3250 kv on 200a 4s and y545 or y547 (on the limit) leo 4092 - 1730kv-2000kv on 240a 6s and h4 or y547 nutto setups comparing the neu 1527 1d(2300kv) and the leo 4092 (2000kv) on 6s on 240a esc the results are similar on the water with the same...

sorry entropy ... doh..not eneloop... here is a link http://shop.rcboatbi...products_id=807 6s 5800ma 50c i use speedmaster welded shafts and tighten the collet really tight .. almost snap in half tight.. 1450 to 2047 is a big jump .. perhaps 1450 ,1647, 1745, 1943, 2040, 2137 would be a...

thanks chilli .. but the motor is in a different compartment in the boat .. :) reading some peoples posts , thanks for all the prop suggestions ... i do like the y5XX its a freaky series of props that allow you to keep the rpm right up on the motor...occtura do a range of 17XX props ...

i am running a 1d 1527 2300kv on a swordfish 240hv on 6s , and i have found the y547 prop to be pretty **** quick with some work done to the prop for heat raceing type setup .. . ,, the abc s15 is much faster, and the 1940 and 2139mod sweet. .. but i want to know what is a safe temp for a...

the tub is your biggest limit on that ,,, but get a 50,000rpm motor , the biggest esc you can fit in there , and start playing with 19--, 20-- and 21-- series , 30mm - to- 40mm octura props and you will see good speed , loose the turnfin and use alot of room .. good luck and curious what you...

lol , this looks so safe jase

http://www.prop-shop.co.uk/index.php?id=40&section=store&sub_section=products&product_type=40 prop shop sell a few teather props from a 4230 , to a 6531 .... such huge pitch on these props , they would no doubt be crazzzzy fast , if you could launch them ! jase

propshop 4217 2blade or 3blade :) http://www.prop-shop.co.uk/index.php?id=25&section=store&sub_section=products&product_type=25 it all comes down to the density of your chosen packs . , if running lipo, then as the pack runs flat the ESC has to draw more amperage to make up for the loss in...

propshop 4520 2blade

Mr Orlic , any plans to do an exhaust throttle for the 46dd and the keep21? regards jason

does anyone still strip there motors out of the box anymore to clean out the flushing from machining ? i have always hated to do this , to risk damaging a brand new engine with my fumble fingered disasembly .... my most sucessfull break in procedure from new ... was take the motor out of the...

it would be nice if jerry would make a 60 inch heat racing hull , the 47 isnt really up to the new hipo motors these days take the 60-80 sd3 boat and make it 60 inches long like your work jase

that gas twin is like looking into the future , amazing boat , nothing goes faster for such a small amount of fuel...period nitro and lipo , is such a huge cost IN mph/dollar , is just a joke compared , i love high nitro even with its expence , and i love expensive electric , but i can...

Im not sure , the motor seized, and is still locked tight now.. i havent pulled it apart , but the pistons floating , so it looks like it could be a wrist-pin failure. i am sending it back to the supplier and asking it to be returned to italy. as thats just not on ... so no look inside yet for...