Seaducer 20 hybrid

larcor69 · Sunday at 11:52 AM

Headed out to the pond yesterday and I raised the strut as far as I could which wasn't very far cuz my whole in the rear of the transom is not that big I also moved the fuel tank closer to the engine about 3 in and it helped a little bit but it still runs like it's just plowing the water and I don't have a very good speed with it , seems like pushing the strut down lower would help lift the transom up higher which seems like logical choice, that will have to remove the stuffing tube and make the hole a larger so I can raise the strut up higher yet it's not much bigger than the quarter inch hole itself hopefully I can get one more chance to throw it in the water before the water gets hard

David Krienke · Sunday at 12:41 PM

When I took the pictures of mine it sure looked like I had a lot of positive angle in the strut as well as being up pretty high. and if you look at the instruction pictures they also have a lot of positive in the strut .

Jeff Barnes · Sunday at 3:27 PM

What prop you running Corey have you tried a 1614 /3 cleaver

larcor69 · Sunday at 3:59 PM

Enlarge the hole and I raised the strut and added some more angle in it running an x440/3

Roxyflash · Sunday at 4:54 PM

I always slot the hole for strut so I can raise it up at least 1/4 inch if needed that rudder still looks way to long.how far below the strut does it measure?

larcor69 · Sunday at 5:23 PM

Roxyflash said:
I always slot the hole for strut so I can raise it up at least 1/4 inch if needed that rudder still looks way to long.how far below the strut does it measure?

I never measured the length of it I just installed it where it said I guess I could cut it to the length it shows in the instructions

Jeff Barnes · Sunday at 5:26 PM

1614 cleaver would loosen it up

FloridaScaleBoater · Sunday at 5:51 PM

larcor69 said:
I never measured the length of it I just installed it where it said I guess I could cut it to the length it shows in the instructions

Really,,,
This was questioned in post #6
Now we've decided to read/follow the instruction book!!

larcor69 · Sunday at 6:36 PM

FloridaScaleBoater said:
Really,,,
This was questioned in post #6
Now we've decided to read/follow the instruction book!!

I didn't feel the little bit of extra length would really make that much of a difference

tnrcboatracer · Monday at 1:25 PM

Blade length can make a huge difference. Also rounding the bottom vs flat bottom. If you are worried about making it too short, start 1/4-3/8" deeper than instructions. IIRC the blade starts out over 1" too long. If boat gets too loose, or if water too rough, you can tighten the boat up by adding a flag of 3M radio box tape to the bottom of the rudder.

FloridaScaleBoater · Monday at 1:42 PM

tnrcboatracer said:
Blade length can make a huge difference. Also rounding the bottom vs flat bottom. If you are worried about making it too short, start 1/4-3/8" deeper than instructions. IIRC the blade starts out over 1" too long. If boat gets too loose, or if water too rough, you can tighten the boat up by adding a flag of 3M radio box tape to the bottom of the rudder.

Jerry's instructions are pretty specific.
And his extensive testing and knowledge of his hulls,,
Well I think at the end of his manual states:
Try it my way first,,, if your not happy with the results. Then do it your way.

Seaducer 20 hybrid

Help Support Intlwaters:

larcor69

Well-Known Member

Attachments

David Krienke

Well-Known Member

Jeff Barnes

Well-Known Member

larcor69

Well-Known Member

Attachments

Roxyflash

Well-Known Member

larcor69

Well-Known Member

Jeff Barnes

Well-Known Member

FloridaScaleBoater

Well-Known Member

larcor69

Well-Known Member

tnrcboatracer

Well-Known Member

FloridaScaleBoater

Well-Known Member

Similar threads

Latest posts

Seaducer 20 hybrid

Help Support Intlwaters:

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!