Seaducer 20 hybrid

larcor69 · Nov 2, 2024

Built a hybrid 20 and oh boy does it run wet and slow, I asked Jerry to help Mark where the engine should go and he said there's too many variables to mention so whatever I put the engine in the area that should have the engine and the radio equipment is in the equipment radio area but it runs really wet actually drags it down slow

larcor69 · Nov 2, 2024

timothy johnson · Nov 2, 2024

Start raising the strut.

larcor69 · Nov 9, 2024

I've raised it and put some positive angle in it hopefully I can run it again this coming Saturday looking forward to seeing if there's any improvements

larcor69 · Nov 9, 2024

Pic of strut

Roxyflash · Nov 9, 2024

That rudder looks way too long the picture is deceiving

David Krienke · Nov 9, 2024

delete

David Krienke · Nov 9, 2024

delete

FloridaScaleBoater · Nov 9, 2024

Roxyflash said:
That rudder looks way too long the picture is deceiving

I'm seeing the same thing.
Did you trim the rudder to Jerry's specs?

David Krienke · Nov 9, 2024

delete

David Krienke · Nov 9, 2024

delete .Sorry to mess up thread. My measurements probably would be different than your hybrid. Mine is a sd3

larcor69 · Nov 9, 2024

Roxyflash said:
That rudder looks way too long the picture is deceiving

It's a sea deucer 21 rudder mounted per the instructions
Hopefully I can run it again this coming week end with the changes I've made if that's still not enough angle and raising it high enough I'll have to make the hole a little bigger so I can raise it higher it's about at its limit right now, I haven't run it since I changed it to the way you see it now yet

Jeff Barnes · Nov 10, 2024

Corey on my seaducer my stut runs high and pretty neutral your stuffing tube has to be able to lift up and down also to help keep strut neutral keep rudder straight if you tuck it under it will dig in the turns

ACTION JACKSON · Nov 10, 2024

Is this first generation 21 or later. Jeff may be right about raising strut.

larcor69 · Nov 10, 2024

ACTION JACKSON said:
Is this first generation 21 or later. Jeff may be right about raising strut.

It's the latest greatest hybrid 20 mono

ACTION JACKSON · Nov 10, 2024

Okay thank you I was just wondering what model it was if you had the generation one seducer I had the paperwork on those. Hope you get your problem worked out

FloridaScaleBoater · Nov 10, 2024

larcor69 said:
It's the latest greatest hybrid 20 mono

Have you reached out to Jerry for his thoughts on what to do?

SayMikey · Nov 10, 2024

Stroke the transom right at the edge under the boat four or five times with a piece of 600 grit on a flat piece of wood

FloridaScaleBoater · Nov 10, 2024

SayMikey said:
Stroke the transom right at the edge under the boat four or five times with a piece of 600 grit on a flat

Sounds like you've talked to Jerry before!!

larcor69 · Nov 10, 2024

When I get a chance to try my changes then I will go from there, I appreciate everybody's input

Seaducer 20 hybrid

Help Support Intlwaters:

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!