45" Dumas scarab, a classic.

Shop deals on ebay
Advertise with us
shop deals on amazon
Intlwaters

Help Support Intlwaters:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
J

Justin "BeaVe" BeVier

Active Member
Joined
Jul 18, 2024
Messages
32
My uncle and brother put thos boat together almost 20 years ago. It hasn't seen the water in quite awhile.

It's a 45" Dumas scarab powered by a modified BH Hanson zenoah G230pum, I don't know the extent of the modifications, but my uncle had a friend at BH Hanson that sent him the piston.

So far I've removed and cleaned the entire fuel system, replaced the futaba magnum Jr. Radio with my radiomaster mt12, and replaced the nicad receiver pack with a NIMH pack, I was getting the throttle trim setup and lost power to my radio, there is a short in the wires somewhere, I ordered some xt-60 plugs to build a "key" that needs to be inserted to power the radio gear up.

What sort of speeds should I expect with this combination with the hull properly setup?
 

Attachments

  • PXL_20240721_203412362.MP.jpg
    PXL_20240721_203412362.MP.jpg
    6.2 MB
Did some reworking of the radio box, the wire that was in it for a switch had a short in it so I needed to replace the switch. What I decided on was this setup, xt-60 plug on the front is connected directly to my receiver pack, the plug in the rear is connected to the receiver. This allows me to charge the receiver pack without removing it from the radio box(NIMH pack, not lipo)
 

Attachments

  • PXL_20240724_072117959.MP.jpg
    PXL_20240724_072117959.MP.jpg
    6.4 MB
The return to the water was tonight.

I've got a couple little kinks to work out seems like it's got a ton of acceleration but no speed. I'll have to do some setup
 

Attachments

  • PXL_20240725_001020508.MP.jpg
    PXL_20240725_001020508.MP.jpg
    6.5 MB
Post a picture of your strut and prop that rooster is really high needs some adjusting and possible a different prop
 
I wanted to mention that boat is pretty cool and would deserve a new engine someday. I bought one of those 138 dollar engines off ebay with the black cooling cap and put it in my 42 inch seaducer and it really runs nice. 19400 rpm pulling a 6717 4 blade prop.. around 54mph. you might think about that sometime. I bet Joe at zippkits if you email him he might know a prop that he has to use on that 230 of yours wouldn't hurt to email him.
 
Justin BeaVe BeVier said:
Honestly. I'm not sure, it's a prop my uncle sharpened and balanced. Here is a video from the first run.
Click to expand...

Dude,,,,, please don’t ever do that again….

I cringe when I see anyone pick up a boat and spin the prop end towards them like you did at the start of your video… I am saying this for your own safety and for anyone that watched your video. It only takes a split second to turn a fun day into a disaster, if that boat slipped out of your hand.
Please be more careful!!!
 
Wasted wages said:
Dude,,,,, please don’t ever do that again….

I cringe when I see anyone pick up a boat and spin the prop end towards them like you did at the start of your video… I am saying this for your own safety and for anyone that watched your video. It only takes a split second to turn a fun day into a disaster, if that boat slipped out of your hand.
Please be more careful!!!
Click to expand...
I saw him do that . He was just super excited to have it going but I agree that is when the bad things happen. Have to mind that prop at all times and be aware its there.
 
Davidkrienke said:
I saw him do that . He was just super excited to have it going but I agree that is when the bad things happen. Have to mind that prop at all times and be aware it’s there.
Click to expand...
I had to rush one club member to the hospital with two of his fingers wrapped in a rag… it wasn’t pretty…

Don’t ever want to see that happen again to anyone…
 
Wasted wages said:
Dude,,,,, please don’t ever do that again….

I cringe when I see anyone pick up a boat and spin the prop end towards them like you did at the start of your video… I am saying this for your own safety and for anyone that watched your video. It only takes a split second to turn a fun day into a disaster, if that boat slipped out of your hand.
Please be more careful!!!
Click to expand...

That was the first thought in my head after I picked the boat up. I'm not doing it that way again. Thanks for looking out.
 
Grimracer said:
Justin.. if you see water shooting up off the prop.. that means it aint shooting back..

You for sure need to try a different prop.. you want a LOW LIFT prop on that boat..

Grim
Click to expand...
Just checked, it's got a prather 275 prop on it.

The strut was adjusted almost all the way up, I lowered it a bit and just did a test run at the lake. Got half a lap then it started down pouring, the lake is 5 minutes away but it sucks when there are people fishing and dogs off a leash, I'm not risking hitting people.
 
Last edited:
Justin BeaVe BeVier said:
Just checked, it's got a prather 275 prop on it.

The strut was adjusted almost all the way up, I lowered it a bit and just did a test run at the lake. Got half a lap then it started down pouring, the lake is 5 minutes away but it sucks when there are people fishing and dogs off a leash, I'm not risking hitting people.
Click to expand...
for an inexpensive prop try a zippkits 6717 3 blade. Even better would be to go to one of the prop sellers on this site and get one already sharpened and balanced.
 

Similar threads

J
Returning to the water after 20ish years
Replies
8
Views
622
Justin "BeaVe" BeVier
J

Latest posts

Back
Top