Search results

Intlwaters

Help Support Intlwaters:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. tnrcboatracer

    MAC 21 OB powerhead. NIB

    Pics added to post #1
  2. tnrcboatracer

    Futaba 75mHz receivers and modules F/S

    I think I still have a few. I brought my radio parts box out of storage to relist them a couple weeks ago, but haven't gotten around to it yet. I'll check tonight when I get home.
  3. tnrcboatracer

    MAC 21 OB powerhead. NIB

    Like the title says, NIB MAC21 OB powerhead. Prepped by Rod Geraghty. Never seen fuel. Includes both water and air cooled head caps. Selling to fund another project. $350 shipped in US48. Will include a complete Irwin Lower with an Oval Express propshaft assembly for $425 total shipped. SPP OB...
  4. tnrcboatracer

    WTB 21 engine for mono

    I have several Novarossi motors you might be intereted in.Both LS and SS. All in the $200~$250 range
  5. tnrcboatracer

    WTB prop pitch gauge.

    Good luck at finding one for $100. I wouldn't sell mine for $300. But I do have an Orlic that I'll part with for $75 +shipping
  6. tnrcboatracer

    CMB 90 Liner removal

    I have bearings for that motor in stock. And I'm sure that Stu does as well.
  7. tnrcboatracer

    ROBBED

    Why wait for your C/C permit? Better to have a permit now, even if you elect not to carry. I know folks that have several handguns on their person at all times, and a loaded AR in their vehicle.......One is enough for me. But you should not carry if you any hesitation about using it if...
  8. tnrcboatracer

    Radio Issue

    I had a similar thing with my 3PJ with FASS module. The boat would bind (solid green) and then start flashing for a few seconds on the starting table, but then re-bound just fine. Not sure what was going on, but it ran just fine after that. I have had 1 received un-bind while in storage (1+...
  9. tnrcboatracer

    Bearing fit on crank

    Angular contact are great on the front end, as they can take more of a thrust load. But you will need a way to shim them, as they are fitted for axial length.
  10. tnrcboatracer

    Bearing fit on crank

    Full compliment bearings are rated for much lower speeds than bearings with retainers. This is due to the rubbing at the contact point between the balls. BUt perhaps the ceramic balls will not be affected in that manner. Good luck. In hte future you might also want to consider angular contact...
  11. tnrcboatracer

    WTB Seaducer 20 mono

    Julian. I have one on the shelf. I can get some pics tonight. I've won several 20 mono races with is in years past. Orangish red deck, green bottom.......
  12. tnrcboatracer

    1500 mAh 6.0V NiMh RX batteries

    Hump. You were interested in the other batteries I had as well. I'll get a list together and make you a package deal.
  13. tnrcboatracer

    Looking for MAC 45 water jacket

    Let me check my parts box when I get back home tomorrow night. Jon
  14. tnrcboatracer

    1500 mAh 6.0V NiMh RX batteries

    I received several NiMh 6V RX batteries with a radio purchase. I run LiFe, so I don't need these. They appear to be fresh. I will test them with a charge/discharge cycle to confirm capacity. Looking for $5/pack with $6 shippiing for 1 or all. I can't remember if there were 4 or 5 packs, and I'm...
  15. tnrcboatracer

    Motor bearings, prop nuts, pressure fittings, SS bolt sets

    Pat, your package is ready to go, but I need your address. Walt, PM sent.
  16. tnrcboatracer

    WTB used ops 67 rod, p&s

    I replied to your email. I have the parts you are looking for. Jon
  17. tnrcboatracer

    WTB Radio Control Boat Modeler Magazines 1995-1999

    I have located the following issues: 9/94, 11/94, 1/95, 2/95, 4/95, 1/96. I have another box of Boat Modellers on a shelf in the garage that I can't get to until Friday evening or Saturday. Do you want any of these issues? jon
  18. tnrcboatracer

    WTB Radio Control Boat Modeler Magazines 1995-1999

    Sure do. Getting ready to move from my home. I'll confirm that I have the issues that you are looking for and PM you. Biggest cost will be the int'l shipping. Jon
  19. tnrcboatracer

    WTB used ops 67 rod, p&s

    Got your email Chas, I was too late at work to go by the storage unit last night. Didn't get home til after 10pm. I will do it tonight. I also have the high speed bearings for the OPS motors in stock. Tom, we have talked before, and could never agree on a price. I still have the 2ea NIB Red...
Back
Top