Search results

I tried the http://www.hobbysoulanges.com/index-en.html and couldn't find a way to shop. Where should I be looking. I am new at this type of conversation. Where should I go from here?

Ok I lost it. I didn't put it away the way I should have. Does anyone know where I may be able to get another. It looks like the outside of the wrist pin is .235" . Thanks

Please let me know how I can contact Brad Christy? I would like to know how much it would cost for a custom Titanium rod for a OPS 80. Thanks

In a previous topic I was looking to correct a carb problem with a OPS80. I burned up the motor and am now looking for a new CMB. The following people were listed as possible sources for these motors: allrc is a distributor in Washington State Stu Barr is the national distributor Jim...

This if good information. Where did you get the information to start? Would this be faster with a single engine? How may batteries of what size are required to make 6 laps?

43" bow to sturn with another 4.5" to the front of the prop. This is a old fiberglass mono hull. Not sure who made it. I would have taken a picture however I don't have a digital camera.

Believe it or not I just burned up my nitro motor. I believe it is time to look at electric. Who can I start talking to? I believe I have far too many questions to try to include them on a great forum like this. Thanks Pat

Believe it or not I just burned up my nitro motor. I believe it is time to look at electric. Who can I start talking to? I believe I have far too many questions to try to include them on a great forum like this. Thanks Pat

This looks just too cool. I have an old mono that I just destroyed the engine in so I decided to go electric. I have so many questions I am not sure where to start. Can you tell me who you talked to get everything put together and working? Thanks so much. Pat

I have Googled several different thing to find replacement parts for my OPS80. I tried RC Nitro Marine engine parts, RC Nitro Marine engine as well as many more. Who can point me in a direction for find some crank shaft bearings and a connecting rod? Please help. Thanks

Some time ago I was looking for information about the motor I purchased for my old mono. I believe someone stated something about the piston rod may give up. Well it did. I was trying to get some throttle control and I didn't get the cooling water running quick enough. Took the poor thing...

I am still working on this OPS80. The silicone tube that came with the header moves arronud. I have held it somewhat in place with wire ties. This doesn't look as if it would hold for verry long. Can I make or purchass something better? Thanks Pat.

Ok, it sounds like the OPS AE85002US is an ok motor if I glue in the carb and install a different piston rod. I know "BOAT" stands for "bring over another hundred" however I thought that was only for my 330SS. Now that that is off my chest what motor should I have purchassed? This will be...

Ok, What an eye opener. Yet again I should have asked more questions before the purchass. It sounds to me like I will need to stick another hundred into this project? Would ime be better to start over with a new engine? What is the recomendation for a good engine this time? Thanks Pat.

Are you telling be that OPS has had this problem for many years and it is still a problem? I thought only GM ran their business that way?

I never heard of GREEN Lock-Tite. Is it removable?

This sounds like the possible removable solution in case I would like to try a larger carb in the futhre? Thanks

I am putting together this old mono hull that I started over 30 years ago. I purchased a OPS AE85002US .80 motor for the power. I had it almost complete and took it outside to do a bench run. I hooked us some water, fuel and everything else I could think of. Started the motor and started to...

After looking at the title I started with, I must hope your mind is on my RC boat. I have an old 42" deep V mono hull that I am installing a .80 OPS nitro motor in. Some think that the motor may be too large. Hope to find out this year. I would think that the best bend in the flex shaft is...

I know this should be so simple, however I don't like anything I have seen or tried to date. I am still rebuilding this old mono. I have come down to the switch to turn on the reciever in the boat. Is there a web page that may have several different layouts of the radio box. Does anyone have...