Fiberglass Hydro Cowlings

Tom Foley · Jan 20, 2012

I now have molds for the following cowlings :

Roadrunner 21 - fits many boats .

Roadrunner 40-67 Offset cowl . Will also fit many boats whether the engine is offset or not ."UP CARB" or low .

Roadrunner 90 Offset cowl . will also fit many boats .

Roadrunner old style low Twin cowl .

Roadrunner VIOLATOR bubble style Twin Cowl , fits "UP " carbs.

Eagle SG 20 cowl , can fit many boats .

Eagle SGX , SG 67-80 cowl .

Email me for more info , std Fiberglass layup .

[email protected]

John Knight · Jan 21, 2012

Tom,

You have an e mail.

John

Tom Foley · Jan 23, 2012

John , I'll give you a call

RodneyPierce · Jan 23, 2012

Tom, can you post a picture of the .21 cowl by chance? Thanks man!

Tom Foley · Mar 10, 2012

A new cowl is available for 5 " tubs . It is a high carb clearance cowl offset to the right based on the old Roadrunner 90 cowl . I will post pics . Thanks .

Mike Byer · Mar 13, 2012

How wide is the Violator cowl

Tom Foley · Mar 13, 2012

New Cowl for offset engine installs , 5 " tub .

Tom Foley · Mar 13, 2012

Mike Byer said:
How wide is the Violator cowl

Fits roadrunner 80 - 90 - 7 " tubs . Should fit any 7 " tub .

Daniel Richard · Mar 16, 2012

If Tom doesn't have what you need try Tamalito. He makes a really nice ABS cowl for the jae and it will also fit other boats.

John Knight · Mar 17, 2012

The cowl in post #7 was for me. It is a good thick fiberglass cowl that will hold up to the thrashing a 90 boat will give it. An ABS one likely would not hold up to the punishment over time. Tom actually used 2 different cowls, cut them to the correct angles and size, then feathered them together, created a mould and then was finally able to build the actual cowl. This was due to not having a mould for my particular hull and the work was very good. He went out of his way to build it for me. Well done!!

Tom Foley · Mar 19, 2012

Pulsetech said:
Tom i am looking for a cowl that will fit a JAE .45 with a Nova .46

i have the 180 degree header engine.

I need to know how high the cowl is right behind the engine as the cowls i have here

are to close to the carb

Greg

How wide is your tub and can you post a pic with the engine in place and a ruler in the photo to show size ?

Tom Foley · Mar 19, 2012

John Knight said:
The cowl in post #7 was for me. It is a good thick fiberglass cowl that will hold up to the thrashing a 90 boat will give it. An ABS one likely would not hold up to the punishment over time. Tom actually used 2 different cowls, cut them to the correct angles and size, then feathered them together, created a mould and then was finally able to build the actual cowl. This was due to not having a mould for my particular hull and the work was very good. He went out of his way to build it for me. Well done!!

Thanks John . I try to give enough glass for strength without going overboard but also keep it light . they will withstand violent crashes and not self destruct . !!

Tom Foley · Mar 22, 2012

OK great .

adam larvenz · Apr 22, 2012

how much for a EAGLE 67 - 80 cowl shipped to lower 48 thank you

Tom Foley · Apr 23, 2012

Which one of the lower 48 do you live in ?

Should be 55.00 $

MXNERD · Sep 13, 2012

Tom do you have a cowl for twin Roadrunner Extreame ?

Tom Foley · Sep 13, 2012

MXNERD said:
Tom do you have a cowl for twin Roadrunner Extreame ?

Yes , what model do you have ?

rick lindow · Sep 16, 2012

Tom, I would like to buy one cowl ! my cowl is (5" wide x 16.125" long) the tall 90 Offset cowl is what I need , my RR is a 60/80 , I'm running a mac 67. Please let me know the total and what type of payment you would like. I would also like you to send me a pic of the Roadrunner VIOLATOR bubble style Twin Cowl , fits "UP " carbs. I have a jag 2 twin, with hr 91's that i would like you to give me your opinion based on these measurements, do you think i could run the cowl ? The tub is 7" wide , from the front of the cowl to center of the motors is 10.125" long , from the center of the mtr's to the rear of the cowl is 6.50" the total cowl length is 16.625" , the measurement of the motor. compartment (side of cowl to center of left mtr 1.75") x (center of mtr. to center of mtr. 3.50") x (center of the right mtr. to the right side of cowl 1.75"). Tom the foot print of my cowl appears to be flat, it will be ok if it has a minimal rise to the cowl maybe 1/8" located in the middle of cowl ! Please let me know what you think and what is the price of the twin cowl? pm me, thanks, Rick Lindow

mick_vankampen · Sep 19, 2012

Hello,

I need a cowl for a Zipp Kits Gas Rigger. http://zippkits.com/~zippkits/index.php?main_page=product_info&cPath=70&products_id=319

The motor I will be installing is a Quickdraw Pioneer 29 and they make strong statements about what type of shields wont work, but it’s not clear to me what will. http://www.quickdrawengines.com/Page_218.html

What do you guys think?

Thanks. -Mick

Tom Foley · Dec 15, 2012

Sorry for the delayed response , we do not offer one that will work with the Zippkitts rigger .

Fiberglass Hydro Cowlings

Help Support Intlwaters:

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

New Member

Well-Known Member

Similar threads

Join the conversation!

Join today and get all the highlights of this community direct to your inbox. It's FREE!